Minecraft InfiniTubes Mod [1.7.10/1.7.2/1.6.4/1.5.2]

Minecraft Mods — July 8, 2014, 8:30 AM - 2,876 Views

InfiniTubes mod provides a way to move items from A to B, by labeling them.

This is a teleposer. It has an input side and an output side (both of which can be set in the GUI), and moves items from the input side to the output side. The input side has a black centre, and the output side has a white centre.

Notice each side of the block has different coloured lights on it. Each direction corresponds to a colour, to allow you to select them in the GUI.

It also has a GUI that looks like this: (don’t panic)

The two coloured squares show the current input and output sides. Left or right click to cycle through the possible sides. Note that you can set them both to the same side.

In the picture above, the input is on the purple side and the output is on the green side – this is the default setup.

If any items are in the top 9 slots, only those items will be allowed through, like in an RP filter or BC diamond pipe. These are holo-slots, like the diamond pipe (If you don’t know what that means, try it and see).

Ignore the textboxes and priority for now.

This is the simplest useful setup with a teleposer. There is a chest next to the input, and another chest next to the output. Items will be moved from the input chest to the output chest. The chests could be replaced with machines or other inventories.

These are transport conduits. They can be used to move items instantly between different teleposers. They can be covered in microblocks, but the microblocks currently will not affect connections between conduits – they will be purely aesthetic.

It doesn’t matter how your conduits are connected. These two conduits are exactly equivalent, except for the materials used to make them:

Item stacks travelling through transport conduits have a label, which can be any text string. They will go to the highest-priority connected teleposer with a matching item filter (or no item filter) and a matching label.

Remember those textboxes in the GUI? They’re for labels.

The “out” textbox specifies the label items will get when they leave this teleposer, and the “in” textbox specifies which labels are allowed to enter the teleposer.

The “in” text can be a |-separated list of labels to accept, which can include * as a wildcard. The “out” text is a ,-separated list of labels to try sending the item to.

For example, with this configuration:

the teleposer will accept diamonds which are labelled either “asdf”, or anything that starts with “sorting”. It will then send them to any teleposer labelled “valuables”. If no teleposer can accept the item (perhaps the valuables chest is full) it will send them to “recycler” instead.

The last block is the transpressurizer. Teleposer networks require power to run, and the transpressurizer converts electricity into a form the network can use. Connect a transport conduit to the top, and an IC2 cable to any other side, and power will be converted until the network is full. It will accept any voltage.

It can also be powered from BC conductive pipes.

1 MJ provides the same amount of power as 2.5 EU.

If you don’t have IC2 or BC or just don’t want to supply power, there is a config option you can use to disable the power requirement of teleposers.

Note that power is used every time a teleposer tries to push an item stack onto a network, even if none of the items could find a destination.

A network can store quite a bit of power, and there is currently no way to measure stored power on a network.

Exact behaviour: (optional reading)

A teleposer uses 3 charge units whenever it attempts to push an item stack, plus one charge unit per item in the stack. If there is not enough stored energy to push the entire stack, it will not do anything, even if there is enough to push part of the stack.

0.8 MJ or 2 EU are required for 1 charge unit.

The maximum stored energy in a network is 128 charge units for every connected machine side.

This is a dislocator. It acts somewhat like a retriever in RedPower, but it can send items to other places as well.

Its GUI looks like this:

The direction is pretty straightforward – it sets the side of the block that connects to a tube network.

Each time the dislocator receives a redstone signal, it does the following:

[list]

How to install InfiniTubes Mod for Minecraft:

• Requires Forge and Immibis Core.
• Download InfiniTubes mod
• Put the downloaded jar file in your mods folder.

Developer: immibis

Download InfiniTubes Mod for Minecraft:

For Minecraft 1.7.10

InfiniTubes  Mod 1.7.10

For Minecraft 1.7.2

InfiniTubes  Mod 1.7.2

For Minecraft 1.6.4

InfiniTubes  Mod 1.6.4

For Minecraft 1.6.2/1.6.1

InfiniTubes  Mod 1.6.2

For Minecraft 1.5.2

InfiniTubes  Mod 1.5.2

For Minecraft 1.5.1

InfiniTubes  Mod 1.5.1

For Minecraft 1.4.7

InfiniTubes  Mod 1.4.7